An excellent way to increase your sense of security while driving is to install a dash camera in your car. Dash cameras may improve safety both inside and outside your vehicle. These tools are excellent, fair "witnesses" to submit to the authorities or for damage claims. Furthermore, they're excellent instruments for documenting the many forms of reckless driving which take place on the roads each day.

The first thing seems to be to purchase a dash camera, and the following is appropriately installing it.

Here's all the information you need to install your new dash camera inside your vehicle correctly.

Hardwiring Installation Procedure

Hardwired power supply cable

The conventional technique for hardwiring is attaching hardwiring equipment to the fused box of your car. You must connect each wire inside your hardwiring equipment to either a continuous circuit (usually color red). In contrast, the other line must be connected to something like an ACC/ignition-switched fuse (commonly yellow). Then, your final line, which should resemble a loop or perhaps a C, should be connected to the metallic ground bolt.

You will utilize a Powered Input Hardwired Connection to do a hardwire on the dash cam external battery pack; you simply have to attach the first ACC (ignition-switched) circuit and the remaining line to something like a grounded bolt. You should particularly plug your dash camera battery pack into the final socket.

Here is the step-by-step guide to help you properly install the battery on your dash cam.

Step1: Connect your input wire towards your dash cam external battery pack when the power switch for that battery pack is set to the OFF setting.

Step2: The auxiliary power distribution breaker should then be found and removed by opening the inside fuse box of your car. It requires a fuse of at least 20 A.

Note that the Accessory Power (known as ACC) primarily provides electricity while the engine runs.

Step3: After inserting the input wire further into the fuse tap's termination sleeves, you may use equipment like a piler to squeeze its sleeve to keep that wire in place firmly.

Step4: Attach the ACC connections throughout the breaker box with the add-a-fuse to something like a fuse that is 20A or bigger.

Step5: Link your vehicle's body or similar metal piece or surface to something like the black line (grounded) connector.

Note that if somehow the bolt on the car is covered, such a covering may prevent the proper supply of electricity.

Setting Up the Output Cable

Step6: Three wiring endpoints, Black (GND), B+ (the color Yellow), as well as ACC, would be present in its output connection (the Red one). Cut and attach the three endpoints of such output connection to the hardwiring wire's appropriate colors. To fasten, apply good electrical tape.

Step7: Using the accompanying Velcro adhesive, fasten your dash cam external battery pack beneath the driver's or guest's seats, in the glove compartment, or inside your trunk.

Installing/Connecting your Dash Cam

Step8: Direct the power line to where it must go, then plug it into your dash camera.

Step9: Place your External Battery Pack on "HIGH," then start the car.

Note that, take a look at your Battery Pack's status lights. Powering will commence when the "CHARGE" light displays the color red for three seconds.

The dashboard camera would then operate in Continuous Configuration.

Step10: Finally, ensure your dash camera is set into Parking Monitoring Mode by turning off your ignition.

Make sure that Power Saving is turned off in the recording options of your dash camera.

Safety Precautions

Do not:

  • Use wet hands when installing or operating.
  • Install in a place with a lot of humidity or near combustible liquids or gases.
  • Leave this gadget inside a fully enclosed vehicle where it will be subjected to intense heat.
  • Firmly press its lens.
  • Attach cutting or pointed items to the lens and its add-ons.
  • Unplug the Micro SD card during its shutdown and capturing processes.
  • Pause the power supply while upgrading the system.
  • Utilize more electricity than the recommended voltage.
  • Take apart the gadget and the charging wire.
  • Cut the power cord.


Saving, downloading, and sharing dash cam footage has been used to apprehend dangerous criminals, demonstrate every driver's innocence, and safeguard passengers and drivers. You can view many of the essential things ever recorded using your dash cam, but we can't explain every event you could record within dash cam recordings. In addition to being a practical tool for your comfort, dash cams could also assist you in conserving enough time and money during an unexpected accident.